Nylon pleated filter cartridge
Short Description:
EBM/EBN series cartridges are made of natural hydrophilic nylon N6 and N66 membrane, easy to wetting, with good tensile strength and toughness, low dissolution, good solvent resistance performance, with universal chemical compatibility, especially suitable for a variety of solvents and chemical fitration.
EBM/EBN series cartridges are made of natural hydrophilic nylon N6 and N66 membrane, easy to wetting, with good tensile strength and toughness, low dissolution, good solvent resistance performance, with universal chemical compatibility, especially suitable for a variety of solvents and chemical fitration.
Key Features
◇ Membrane have strong alkali resistance, good toughness and dissolutioin content is extremely low;
◇ Passing 100% integrity test, through the high pure water rinse, no fibers shedding;
◇ Natural hydrophilica without pre-wetting;
◇ Resistant to acetone, alcohol and other organic solvents filtration;
Typical Applications
◇ High purity chemicals, ketone, ester, ether, alcohol and alkaline liquid filtration;
◇ Ultrapure water equipment, CD, display and polysilicon ultrapure water filtration;
◇ The pure water, mineral water, fruit juice, beer and wine filtration in food and beverage industry;
◇ Sterile apis, indusion, lyophilized powder needle, buffer solution and reagents aseptic filtration in pharmaceutical industry;
Material Construction
◇ Filter medium: Nylon N6/N66
◇ Support/drainage: PP
◇ Core and cage: PP
◇ O-rings: see the cartridge list
◇ Seal method: melting
Operating conditions
◇ Working temperature:≤80°C
◇ Sterilization temperature: 121°C 30minutes
◇ Maximum positive pressure difference: 0.45Mpa, 25°C
◇ Maximum negative pressure difference: 0.21Mpa, 25°C
Key Specifications
◇ Removal rating: 0.2, 0.45, 0.65, 1.0, 3.0, 5.0 (unit: um)
◇ Effective filter area: single-layered ≥0.6/10”
◇ Outer diameter: 69mm, 83mm, 130mm
Quality Assurance
◇ Endotoxin: <0.25EU/ml
◇ Filtrate:<0.03mg per 10”
Ordering Information
N6: EBM--□--◎--◇--○--☆--△
N66:EBN---□--◎--◇--○--☆--△
|
□ |
○ |
☆ |
|
△ |
||||||
|
No. |
Removal rating (μm) |
No. |
Length |
No. |
End caps |
No. |
O-rings material |
|||
|
002 |
0.2 |
5 |
5” |
A |
215/flat |
S |
Silicone rubber |
|||
|
004 |
0.45 |
1 |
10” |
B |
Both ends flat/both ends passing |
E |
EPDM |
|||
|
006 |
0.65 |
2 |
20” |
F |
Both ends flat/one end sealed |
B |
NBR |
|||
|
010 |
1.0 |
3 |
30” |
H |
Inner O-ring/flat |
V |
Fluorine rubber |
|||
|
020 |
2.0 |
4 |
40” |
J |
222 stainless steel liner/flat |
F |
Wrapped fluorine rubber |
|||
|
030 |
3.0 |
|
|
K |
222 stainless steel liner/fin |
|
|
|||
|
050 |
5.0 |
|
|
M |
222/flat |
|
|
|||
|
100 |
10 |
|
|
P |
222/fin |
|
|
|||
|
|
|
|
|
Q |
226/fin |
|
|
|||
|
|
|
|
|
O |
226/flat |
|
|
|||
|
|
|
|
|
R |
226 stainless steel liner/fin |
|
|
|||
|
|
|
|
|
W |
226 stainless steel liner/flat |
|
||||